How to widen your trailer axle

If you’re looking to widen your trailer axle, there are a few things you’ll need to do. First, you’ll need to remove the old axle. Next, you’ll need to measure the new axle to make sure it’s the right size. Once you have the new axle, you’ll need to install it and then attach the new wheels. Finally, you’ll need to make sure the new axle is secure by adding some brackets. By following these steps, you’ll be able to widen your trailer axle in no time.

How to widen your trailer axle

If you’re like most RVers, you love spending time outdoors, whether it’s traveling down the road or just taking in the sights and sounds of nature. But one of the downsides of traveling in an RV is that it can be difficult to keep up with the pace. That’s where your trailer comes in handy.

Trailer tongues are typically limited in width, which can make it difficult to pass other vehicles or even get around tight corners. If you want to travel the country in relative comfort, you need to widen your trailer axle.

There are a few ways to do this. One is to use a professional widening service. This is a popular option for people who don’t have the time or inclination to do it themselves. However, it can be expensive, and it’s not always available where you need it.

Another option is to widen your trailer axle yourself. This is a DIY project, but it’s not as difficult as you might think. And it’s definitely cheaper than hiring a professional.

Here are eight tips to help you get started:

1. Do your research. If you decide to do the project yourself, be sure to research the specific axle widths that you need. There are a lot of options out there, and it can be difficult to figure out which one is right for your trailer.

2. Buy the correct tools. You’ll need a set of axle widening tools, as well as a pair of pliers or a wrench.

3. Get a clean, safe workspace. You don’t want any oils or other substances on the axle surfaces

Why you might want to widen your trailer axle

One of the most common reasons people have their trailer’s axle widened is because the original axle size is not wide enough to fit the trailer’s load. By widening the axle, you can increase the trailer’s carrying capacity and make your trip more enjoyable.

How to measure for a wider axle

If you tow a trailer with a standard axle, it’s possible to increase the width of the axle by using a wider axle. There are a few different ways to do this, but the most common is to use a spline axle. Here’s how to measure for a wider axle:

1. Remove the wheel and axle from the trailer.

2. Use a caliper to measure the inside width of the axle housing. This should be the same width as the spline axle you plan to use.

3. Install the spline axle and wheel.

4. Reconnect the axle housing and re-measure.

5. If the axle housing still measures the same width as the spline axle, the axle is ready for use.

6. Otherwise, you’ll need to remove the axle housing and enlarge it using a grinder or a Dremel tool.

7. Reattach the axle housing and re-measure.

8. If the axle housing now measures wider than the spline axle, you’re good to go.

How to install a wider axle

If your trailer axle is too narrow, you can install a wider axle to improve your trailer’s handling and stability. A wider axle will also make your trailer more stable when you’re towing a heavy load. Here are three easy steps to installing a wider axle.

1. Measure the width of your axle. Most trailer axles are between 2 and 2 1/2 inches wide.

2. Buy a new axle. If your axle is too narrow, a wider axle will improve your trailer’s stability and handling.

3. Install the axle. Most axles are installed by hand. Follow the manufacturer’s instructions to install the axle.

4. Check the fit. After the axle is installed, check the fit by making sure the axle is seated in the hub and the nut is tight.

5. Adjust the fit. If necessary, you can adjust the fit of the axle by adjusting the nut.

6. Test the trailer. After the axle is installed, test the fit by towing your trailer.

7. Enjoy your new axle.

How to troubleshoot a wider axle

If you notice that your trailer axle isn’t widening as it should, there are a few things you can do to troubleshoot the issue. In this article, we’ll outline the most common culprits and the solutions you can use to fix them.

1. Check the ball bearing clearances.

If the axle is rubbing against the ball bearings, it can cause the axle to wear and warp. To check the clearances, you can use a dial gauge or a feeler gauge. Be sure to tighten the axle nut just enough so that the gauge doesn’t move, and then check the clearance again. If the clearance is too tight, you can either remove the axle nut and try to adjust the clearances, or you can install a new set of ball bearings.

2. Check the axle nut.

If the axle nut is loose, it can loosen and cause the axle to rub against the ball bearings. To check the nut, you can use a nut driver or a socket and ratchet. Be sure to tighten the nut just enough so that the torqueometer doesn’t move, and then check the clearance again. If the clearance is too tight, you can either remove the axle nut and try to adjust the clearances, or you can install a new set of ball bearings.

3. Check the hub.

If the hub is out of alignment, it can cause the axle to rub against the ball bearings. To check the hub, you can use a feeler gauge or a dial gauge. Be sure to tighten the hub nut just enough so that the gauge doesn’t move, and then check the clearance again.

How to maintain a wider axle

If your trailer axle is too narrow, it can cause your trailer to bounce and shake when you drive. This is called axle bounce, and it can be really annoying.

To fix this problem, you need to widen your axle. There are a few different ways to do this, and each one is a little different. You can either use a hydraulic axle widening tool, a hammer and chisel, or a drill and screwdriver.

whichever method you choose, be sure to follow the instructions carefully. Otherwise, you could end up damaging your axle or your trailer.

Conclusion

if you want to widen your trailer axle, you’ll need to purchase a new axle, weld it to the frame, and then re-install the wheels. This process is not for the faint of heart, but if you’re up for the challenge, you’ll be able to reap the rewards of a wider trailer axle. Just be sure to take your time, and be extra careful when welding.