How to change your oil in a FJ Cruiser

If you own a FJ Cruiser, it’s important to know how to change your own oil. Not only will this save you money, but it will also help you keep your car in tip-top shape. Here’s a step-by-step guide on how to do it:

How to Change Oil 07-14 Toyota FJ Cruiser


Open the hood and locate the oil fill cap

If you’re like most FJ Cruiser owners, you probably don’t want to mess with your engine too often. But every now and then, it’s worth checking the oil level and replacing the oil filter. Here’s how to do it yourself.

First, open the hood and locate the oil fill cap. It’s usually on the left side of the engine near the gasoline filler neck. Next, use a wrench to unscrew the cap. Be careful not to lose any of the oil that’s already in the engine.

Remove the old oil filter and discard it. Pour about a quart of new oil into the engine and replace the cap. Make sure the oil filter is seated properly and tighten the screw on the oil filter cover.

That’s it! Your FJ Cruiser is now ready for another 500 miles of trouble-free motoring.

Unscrew the oil fill cap and set it aside

You may have noticed a small oil fill cap on the FJ Cruiser’s engine. This cap should be unscrewed and set aside. Next, use a funnel to pour oil into the engine until the level reaches the “Max” line on the dipstick. Replace the cap and screw it on securely.

Locate the oil drain plug and place an oil catch pan beneath it

If you’re experiencing problems with your FJ Cruiser’s engine, the first place to check is the oil drain plug. This is a small, round component located beneath the engine oil pan. To change the oil, first locate the plug and place an oil catch pan beneath it. Next, unscrew the plug with a wrench and pour new oil into the pan. Be sure to replace the plug and tighten the wrench before reassembling the engine.

Unscrew the oil drain plug and allow the oil to drain

If your FJ Cruiser has been sitting for a while, it’s time to unscrew the oil drain plug and allow the oil to drain. This is a common maintenance procedure that you should perform every 3,000 miles or every six months, whichever comes first. Here’s how to do it:

1. Park your FJ Cruiser in a level, safe place.

2. Remove the spark plugs.

3. Remove the oil filter.

4. Remove the oil drain plug.

5. Allow the oil to drain.

6. Replace the oil filter, oil drain plug, and spark plugs.

7. Reinstall the vehicle components.

Screw the oil drain plug back in and remove the oil catch pan

If you’re like most drivers, you’ve probably replaced your oil at least once, maybe twice, during your time behind the wheel of a FJ Cruiser. And while changing your oil is a necessary task, it’s also a pretty involved one. But don’t worry, we’re here to walk you through the whole process.

First, remove the oil catch pan by unscrewing the two torx screws located at the top. Be sure to note where the pan was before you remove it, as you’ll need to reinstall it in the same spot when you return the pan to its original position.

Next, remove the old oil filter by unscrewing the two bolts located on either side of the engine. Again, take note of where the filter was before you remove it, as you’ll need to reattach it in the same spot.

Now it’s time to get your new oil filter and oil. Make sure to get a filter that’s the correct size for your engine. The oil should come in a plastic bottle that has a cap. Once you have the oil, pour it into the engine and replace the filter and bolts.

Finally, replace the oil catch pan by screwing it back in to the engine and tightening the torx screws. Be sure to check to see if the pan lines up exactly where it was before you removed it, as you don’t want to start the installation and then have to re-do it.

Pour in new oil and screw the oil fill cap back on

Change your FJ Cruiser’s oil every 3,000 miles or when the oil level reaches the “max” indicator on the dashboard. The “max” indicator is a yellow arrow that points up when the oil level is high.

To change your oil:

1. Open the hood.

2. Locate the oil fill cap.

3. Unscrew the oil fill cap.

4. Remove the old oil.

5. Install the new oil.

6. Screw the oil fill cap back on.

Close the hood and enjoy your clean oil!

If you’re like most Jeep owners, you’ve probably changed your engine oil at least a few times. Changing your oil is a routine maintenance task that’s important for your vehicle’s longevity. Here’s how to do it in a FJ Cruiser. . . .

1. Make sure your engine is cold before you start. This will help prevent damaging the engine due to the oil being hot.

2. Remove the oil pan. On most Jeeps, the oil pan is located on the right side of the engine under the vehicle.

3. Open the oil drain valve. This is usually located on the side of the engine near the oil pan.

4. Pour the new oil into the engine. Be sure to use the correct oil drain plug.

5. Replace the oil pan and tighten the bolts.

6. Reconnect the oil lines and check the oil level. Be sure to add more oil if necessary.

7. Start the engine and check for leaks.


it is very important to change your oil regularly in order to maintain your FJ Cruiser in tip-top shape! By following the simple steps outlined in this article, you can easily do this yourself at home and save money in the process. So don’t put it off any longer, get out there and do it!

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.